H3C 交换机端口镜像与二层转发配置

一、设备与配置范围

本文涉及两台 H3C 设备:

设备名称主要配置
FlowTrafficAuditTest本地端口镜像组 1,源端口 GE2/0/24,监控端口 GE2/0/23
L2Point5SwitchVLAN 100/200、Access 端口、IRF 端口、SNMP/NTP/SSH/Telnet 等

二、FlowTrafficAuditTest 端口镜像配置

1. 配置目标

将 GigabitEthernet2/0/24 的入方向和出方向流量镜像到 GigabitEthernet2/0/23。

2. 关键配置

sysname FlowTrafficAuditTest

mirroring-group 1 local

interface GigabitEthernet2/0/24
 mirroring-group 1 mirroring-port both
#
interface GigabitEthernet2/0/23
 mirroring-group 1 monitor-port

3. 配置说明

  • mirroring-group 1 local:创建本地镜像组 1。
  • mirroring-group 1 mirroring-port both:将 GE2/0/24 作为镜像源端口,镜像双向流量。
  • mirroring-group 1 monitor-port:将 GE2/0/23 作为监控端口。

4. 验证命令

display mirroring-group 1

文档中验证结果类似:

Mirroring group 1:
    Type: Local
    Status: Active
    Mirroring port:
        GigabitEthernet2/0/24  Both
    Monitor port: GigabitEthernet2/0/23

三、L2Point5Switch 基础与 VLAN 配置

1. 基础系统配置

sysname L2Point5Switch

clock timezone Beijing add 08:00:00
clock protocol none

telnet server enable

irf mac-address persistent timer
irf auto-update enable
undo irf link-delay
irf member 1 priority 32

lldp global enable
password-recovery enable

2. VLAN 配置

最终配置中:

vlan 1
 name Default

vlan 100
 description VLAN100

vlan 200
 description VLAN200

3. 端口划分

文档中端口划分如下:

  • GE1/0/1~GE1/0/8:Access VLAN 100,描述为 VLAN100_For 8 device
  • GE1/0/9~GE1/0/17:Access VLAN 200,描述为 VLAN100_For 9 device
  • GE1/0/18~GE1/0/22:仅配置 port bridge enable
  • GE1/0/23~GE1/0/24:用于 IRF 端口
  • GE1/0/25~GE1/0/28:未配置业务

配置示例:

interface range GigabitEthernet1/0/1 to GigabitEthernet1/0/8
 description VLAN100_For 8 device
 port access vlan 100
 port bridge enable
#
interface range GigabitEthernet1/0/9 to GigabitEthernet1/0/17
 description VLAN100_For 9 device
 port access vlan 200
 port bridge enable
#
interface range GigabitEthernet1/0/18 to GigabitEthernet1/0/22
 port bridge enable

注意:文档中 GE1/0/9~GE1/0/17 的描述为 VLAN100_For 9 device,但实际加入的是 port access vlan 200。建议将描述修正为 VLAN200_For 9 device,避免维护误解。


四、IRF 端口配置

文档中使用 GE1/0/23 和 GE1/0/24 作为 IRF 物理成员端口:

irf-port 1/2
 port group interface GigabitEthernet1/0/23 mode normal
 port group interface GigabitEthernet1/0/24 mode normal

同时配置:

irf mac-address persistent timer
irf auto-update enable
undo irf link-delay
irf member 1 priority 32

说明:

  • irf member 1 priority 32 用于设置成员优先级,数值越大越优先成为 Master。
  • irf-port 1/2 表示 IRF 成员 1 的 IRF 端口 2。
  • 实际部署时需确保 IRF 端口加入 irf-port 后,再绑定物理接口,并按需激活 IRF 配置。

验证命令:

display irf
display irf configuration
display interface brief

五、路由与管理配置

文档中曾配置管理 VLAN 接口:

interface Vlan-interface1
 ip address 192.168.10.2 255.255.255.0

并配置默认路由:

ip route-static 0.0.0.0 0 192.168.8.2

但后续执行了:

undo int vlan 1

因此最终配置中已经没有 Vlan-interface1 管理 IP。若需要保留远程管理能力,建议重新配置管理 VLAN 接口和默认路由,例如:

interface Vlan-interface1
 ip address 192.168.10.2 255.255.255.0
 quit

ip route-static 0.0.0.0 0 192.168.8.2

注意:最终配置中仍有默认路由,但如果没有三层接口或管理地址,该路由的实际可用性需要结合现网确认。


六、日志、SNMP、NTP/SNTP 配置

1. 日志主机

文档中配置了日志主机:

undo info-center enable
info-center loghost 192.168.8.156

注意:undo info-center enable 会关闭信息中心功能,可能导致日志无法正常输出到日志主机。若需要日志主机生效,通常应先启用 info-center enable,再配置 loghost。例如:

info-center enable
info-center loghost 192.168.8.156

2. SNMP 配置

snmp-agent
snmp-agent local-engineid 800063A280487397F4C53B00000001
snmp-agent community write private
snmp-agent community read public
snmp-agent sys-info version all
snmp-agent target-host trap address udp-domain 192.168.8.123 params securityname public v2c
snmp-agent target-host trap address udp-domain 192.168.8.20 params securityname public v2c

安全建议:文档中使用了 public/private 作为 SNMP 团体名,属于弱口令,生产环境应更换为强团体名,并结合 ACL 限制 SNMP 访问来源。

3. NTP/SNTP 配置

ntp-service refclock-master
ntp-service unicast-server 192.168.0.12

sntp unicast-server 192.168.0.11

说明:

  • ntp-service refclock-master 表示设备作为 NTP 主时钟参考。
  • 同时又配置了 NTP 单播服务器和 SNTP 服务器,实际部署时建议根据网络规划选择一种时间同步方式,避免配置冲突或维护混乱。

七、远程登录与本地用户

1. VTY 配置

line aux 0
 user-role network-admin
#
line vty 0 4
 authentication-mode scheme
 user-role network-operator
 protocol inbound telnet
#
line vty 5 63
 user-role network-operator

2. Telnet/SSH/HTTP/HTTPS

telnet server enable
ssh server enable

ip http enable
ip https enable

3. 本地用户

文档中创建了多个本地用户,例如 REBECCA、RRR、abc、admin、test,并配置了不同的服务类型和用户角色。配置形式类似:

local-user admin class manage
 password hash ******
 service-type ftp
 service-type telnet http https
 authorization-attribute user-role network-admin
 authorization-attribute user-role network-operator

local-user test class manage
 password hash ******
 service-type http https ssh
 authorization-attribute user-role network-admin
 authorization-attribute user-role network-operator

安全建议:

  1. 文档中暴露了密码哈希,实际文章中不建议公开。
  2. 生产环境应遵循最小权限原则,避免普通运维用户同时具备 network-admin 权限。
  3. 若使用 SSH 登录,VTY 下应配置 protocol inbound ssh 或 protocol inbound all;当前文档中 VTY 0~4 仅放通 Telnet。

八、配置验证命令汇总

FlowTrafficAuditTest

display mirroring-group 1
display current-configuration
display saved-configuration

L2Point5Switch

display current-configuration
display vlan brief
display interface brief
display irf
display ip interface brief
display ntp-service status
display snmp-agent sys-info
display ssh server status